Pdf Ebook Downloadfree automotive repair manual

download
Removal and installation note: 1. Remove the exterior mirror mounting hole cover. 2. If equipped, remove the window regulator handle. Position the window regulator handle cover aside. Remove the window regulator handle screw and regulator handle. 3. If equipped, remove the window control switch plate. Disconnect the window control switch electrical connectors and if equipped, the memory set switch electrical connector. 4. If equipped, remove the front door trim panel reflector or the courtesy lamp lens. 5. Remove the screws. 6. Lift and remove the front door trim panel. 7. If equipped, twist the courtesy lamp connector one half turn and remove it from the front door trim panel. 8. To install, reverse the removal procedure.

download
Wiper/washer (1993) 3 – 30 amp wiper/washer (1994) 4 – 25 amp parking lights 5 – 10 amp rear defrost, eatc, brake shift interlock, traction control switch 6 – 15 amp courtesy lights, power mirrors, dome switch, remote keyless entry (1993), , electronic door lock control (1994), memory seats 7 – 10 amp power antenna, anti-theft relay, memory seats 8 – 20 amp cigarette lighter 9 – 10 amp transmission control switch, autolight sensor, electrochromic mirrors 10 – 15 amp suspension/steering module, electronic flasher, steering wheel position sensor, daytime running lights, back-up lights, air bag (1993), air bag diagnostic monitor (1994) 11 – 10 amp

download
Door window glass – front special tool(s) 1. Remove the front door trim panel. For additional information, refer to front door trim panel . 2. Position the watershield aside. 3. Remove the parts in the order indicated in the following illustration and table. To remove individual parts, only carry out the listed steps: part front door window glass front door window regulator front door glass run 4. To install, reverse the removal procedure. Item 1: rivet removal note 1. Connect the window control switch. 2. Connect the battery. 3. Position the door window glass halfway down to gain access to the door window glass rivets. Remove the rivets. Item 4: rivet removal note 1. Remove the rivets. Item 5: front door window regulator removal note

download
Removal 1. Remove outside rear view mirror remote control unit. 2. Remove window regulator control switch housing by gently prying up, starting at the front. 3. Disconnect all connectors from window regulator control switch housing. 4. Remove inside door handle cup by gently prying at screwdriver slot with a screwdriver. 5. Remove screw directly beneath inside door handle. 6. Remove lower self-tapping screw retaining front door trim panel to door inner panel. 7. Remove rectangular plug in trim panel upper front extension and depress finger bracket with screwdriver. 8. Lift front door trim panel upward and snap out trim panel. 9. Disconnect wire harnesses from door panel as required and remove front door trim panel. Installation 1. Connect wire harnesses to front door trim panel as required. 2. Install front door trim panel by pushing in and down until it snaps into place. 3. Install all self-tapping screws retaining front door trim panel to door inner panel. 4. Install inside door handle cup. 5. Install window regulator control switch housing. 6. Install outside rearview mirror remote control unit.

dowload
Ford focus 2000-05 ignition lock cylinder removal & installation removal & installation 1. Before servicing the vehicle, refer to the precautions section. 2. Disconnect battery negative cable from battery and properly isolate to prevent accidental reconnection. 3. Remove the instrument panel lower panel. 4. Detach the steering column upper shroud. 5. Remove the audio control switch, if equipped. 6. Remove the steering column lower shroud. 7. Insert and turn the ignition key to position I (accessory). 8. Using a thin bladed screwdriver, depress the detent and remove the lock cylinder. Fig. Removal of the ignition lock cylinder. To install: 1. Press the lock cylinder into place and remove the key. 2. Install the steering column lower shroud. 3. Install the audio control switch, if equipped. 4. Install the steering column upper shroud. 5. Install the lower instrument panel cover. 6. Reconnect the negative battery cable. 1. Before servicing the vehicle, refer to the precautions section. 2. Disconnect battery negative cable from battery and properly isolate to prevent accidental reconnection. 3. Remove the instrument panel lower panel. 4. Detach the steering column upper shroud. 5. Remove the audio control switch, if equipped. 6. Remove the steering column lower shroud. 7. Insert and turn the ignition key to position I (accessory). 8. Using a thin bladed screwdriver, depress the detent and remove the lock cylinder.