Pdf Ebook Downloadfree automotive repair manual

download
Repair procedure a 1. Connect the hds to the vehicle’s dlc. 2. Start the engine, and turn on the hds. 3. When prompted, enter the vin and the odometer reading. 4. From the system selection menu screen, select pgm-fi. 5. From the mode menu, select data list. 6. Scroll down the list to psp switch. Watch the reading in the value column. 7. Check for a broken power steering pressure switch wire by wiggling the p/s pressure switch wire harness at the switch while you check the value column reading. • if the reading changes between on and off when you wiggle the harness, go to step 8. • if the reading does not change between on and off when you wiggle the harness, go to repair procedure b. 8. Raise the vehicle on a lift, and remove the right front wheel to access the power steering pressure switch. 9. Disconnect the connector from the switch, and release the harness clip from the body. Note: you may need to disconnect the secondary ho2s connector to free the end of the harness from the body.

download
Repair procedure note: to replace the under-dash fuse/relay box (micu), you need these items: • replacement under-dash fuse/relay box (micu) • one programmed ignition key for the vehicle • hds with software version 2.002.006 or later • pcm code (the 4-digit code is available on the in. Go to service, and select vehicle information from the left column, then select immobilizer code inquiry.) 1. Replace the under-dash fuse/relay box (micu). Note: when you replace the under-dash fuse/ relay box (micu), you must use the hds to register the imoes unit with the immobilizer-keyless control unit. If this procedure is not done after the micu replacement, the engine will not start. • refer to section 22 of the appropriate 2006 civic service manual, or • online, enter keyword fuse box, and select under-dash fuse/relay box removal and installation from the list. 2. Connect the hds to the 16p data link connector 3. Insert the programmed ignition key into the ignition switch, and turn the ignition switch to on (ii). Turn on the hds. 4. At the screen prompts, enter the vin and the odometer reading, and then verify the date and time are correct in the hds. 5. From the system selection menu screen, select immobi. 6. From the immobilizer test mode menu screen, select replace mpcs/micu/imoes, and follow the screen prompts to register the imoes unit. 7. From the pcm-code screen, enter the pcm code, and then follow the screen prompts. When the process is complete, turn the ignition switch to the lock (0) position, and then turn off and disconnect the hds.

download
Procedure 1. Use an appropriate key blank and the matrix h key cutting machine to cut a new ignition key (see s/b 01-077, cutting sidewinder-type keys with the matrix h key cutting machine). 2. Connect the hds to the 16p data link connector (dlc). 3. Insert a programmed ignition key into the ignition switch, and turn the switch to on (ii). Turn on the hds. 4. At the screen prompts, enter the vin and the odometer reading, and then verify the correct date and time. 5. From the system selection menu screen, select immobi. 6. From the mode menu screen, select immobilizer setup. 7. From the immobilizer test mode menu screen, select add and delete keys. 8. From the add and delete keys screen, select add 1 key. 9. From the add 1 key screen, select begin to add 1 key. 10. From the 1st password screen, enter the 1st password, and then follow the screen prompts. When you are finished, turn the ignition switch to lock (0), and then turn off and disconnect the hds. Adding multiple keys use the hds with honda key blanks to add multiple keys. Make sure you use only key blanks with a v stamped on the shank. The hds rewrites the immobilizer control unit-receiver, storing the transponder codes of the new keys in the memory of the immobilizer control unit-receiver.

download
Diagnosis note: you must complete the diagnosis before attempting any cvt repairs. 1. Civic hybrid and insight only: make sure the ima battery level gauge shows at least three quarters charged. If you need to increase the ima charge, do this: • insight only: remove the eps (electronic power steering) fuse from the under-hood fuse/relay box. • start the engine, and run it at 3,500 rpm until the battery level gauge shows at least three quarters charged. • insight only: reinstall the eps fuse. 2. Connect the hds to the vehicle’s dlc, then turn the ignition switch to on (ii), and turn on the hds. 3. At the hds screen prompts, enter the vin (if prompted) and the odometer reading. 4. At the select mode screen, select honda systems. 5. At the system selection menu, select a/t. 6. From the mode menu, select snapshot. 7. Set these snapshot points: • trigger type: manual • recording time: 2 minutes • trigger point: -60 seconds 8. Find a flat stretch of road where you and an assistant can drive for 2 minutes at a steady vehicle speed.

download
Repair procedure note: to replace the under-dash fuse/relay box (micu), you need these items: • replacement under-dash fuse/relay box (micu) • one programmed ignition key for the vehicle • hds with software version 2.002.006 or later • pcm code (the 4-digit code is available on the in. Go to service, and select vehicle information from the left column, then select immobilizer code inquiry.) 1. Replace the under-dash fuse/relay box (micu). Note: when you replace the under-dash fuse/ relay box (micu), you must use the hds to register the imoes unit with the immobilizer-keyless control unit. If this procedure is not done after the micu replacement, the engine will not start. • refer to section 22 of the appropriate 2006 civic service manual, or • online, enter keyword fuse box, and select under-dash fuse/relay box removal and installation from the list. 2. Connect the hds to the 16p data link connector 3. Insert the programmed ignition key into the ignition switch, and turn the ignition switch to on (ii). Turn on the hds. 4. At the screen prompts, enter the vin and the odometer reading, and then verify the date and time are correct in the hds. 5. From the system selection menu screen, select immobi. 6. From the immobilizer test mode menu screen, select replace mpcs/micu/imoes, and follow the screen prompts to register the imoes unit. 7. From the pcm-code screen, enter the pcm code, and then follow the screen prompts. When the process is complete, turn the ignition switch to the lock (0) position, and then turn off and disconnect the hds.