Pdf Ebook Downloadfree automotive repair manual

download
Using the hds 1. Connect the hds to the data link connector. 2. Turn the ignition switch to on (ii), then enter the vehicle’s vin and mileage at the prompts. 3. Select body electrical from the system select menu. 4. From the body electrical system select menu, select power windows. 5. From the mode menu, select adjustments. 6. From the adjustment menu, select window reset for driver’s side (passenger’s side) window. 7. Follow the prompts on the screen. 8. Confirm that the power window control unit is reset by using the power window auto up and auto down function. Without the hds note: do each bullet in step 4 within 5 seconds of each other. The front passenger’s power window must be reset from the front passenger’s power window switch.* *: with front passenger’s power window auto up/auto down function 1. Turn the ignition switch to on (ii). 2. Move the power window all the way down by using the power window down switch. 3. Open the driver’s door. 4. Do the following three times before going to step 5: turn the ignition switch to lock (0). Push and hold the power window down switch. Turn the ignition switch on (ii). Release the power window down switch. 5. Confirm that auto up no longer works. If auto up still works, go back to step 1. 6. Move the power window all the way down using the power window down switch. 7. Pull up and hold the power window up switch until the power window is all the way up, then continue to hold the switch for 1 second. 8. Confirm that the power window control unit is reset by using the power window auto up and auto down function. If the power window still does not work in auto, repeat the procedure several times, paying close attention to the 5 second time limit between steps. If it still does not work, go to b-can system diagnosis test mode a.

download
Resetting the pax system warning resetting the pax system warning when a tire goes flat or, is very low on pressure, the multi-information display will show “pax system warning, run flat driving.” after the tire is repaired or replaced, you must reset the warning indicator (and the mileage counter that supports it), no matter how far the vehicle was driven in the run flat mode. 1. To put the gauge control module into the self-diagnostic mode: turn the headlight switch to on. Press and hold the select/reset (instrument panel brightness) knob. Turn the ignition switch to on (ii). Within 5 seconds, turn the headlights to auto, then to on, and then to auto again. Within 5 seconds, release the select/reset knob, then push and release the knob three times. 2. Once the gauge control module is in the self-diagnostic mode, press and hold the info button on the steering wheel for 5 seconds to get to the customize menu. 3. Use the info button to scroll through to the pax reset screen, then press the sel/reset button on the steering wheel. 4. Use the info button to scroll to the appropriate wheel, and then press the sel/reset button on the steering wheel to reset the pax warning system display. The screen should read pax reset completed. Repeat this step for each wheel that needs to be reset. 5. Use the info button to scroll through to exit, then press the sel/reset button. 6. Turn the ignition switch to lock (0) to exit the self-diagnostic mode.

download
Radio/Stereo: Service and Repair Security Code Instructions ENTERING THE SECURITY CODE If the code has not already been entered, or if power to the set has been interrupted, the code MUST be entered before the set will work. Enter the code as follows: – Switch on the unit by pressing the On/Off button (1) (‘CODE IN’ appears in the display). – Enter the correct security code by pressing the numbered buttons (7) corresponding to the numbers of the code in the right order; eg. If the first digit of the code number is a 3, press pre-set button 3 (the number will then appear on the display). – When the correct code has been entered, the display will show the radio frequency and the radio will operate. NOTE: This process will have to be repeated whenever the unit is disconnected from the power supply. If the wrong code number is entered, the numbers will remain on the display and the unit will not operate. If this occurs, follow the procedure below: – Press and hold the BND (4) button for approximately three seconds (‘CODE IN’ appears on the display). – Enter the CORRECT code number. If the wrong code number is entered three times, a time delay period of one hour commences. After one hour, you can try again. Each time another incorrect code is entered, another hour delay will be activated until the correct code is entered. CATS Indicator To warn potential thieves that your unit is protected by a computer anti-theft system, an indicator light (8) flashes whenever the starter switch is turned off. This light can be either activated or deactivated by the following procedure: – Turn off the vehicle’s starter switch. – Press and hold the BND button (4) for approximately three seconds.

download
Radio/stereo: service and repair security code instructions entering the security code if the code has not already been entered, or if power to the set has been interrupted, the code must be entered before the set will work. Enter the code as follows: – switch on the unit by pressing the on/off button (1) (‘code in’ appears in the display). – enter the correct security code by pressing the numbered buttons (7) corresponding to the numbers of the code in the right order; eg. If the first digit of the code number is a 3, press pre-set button 3 (the number will then appear on the display). – when the correct code has been entered, the display will show the radio frequency and the radio will operate. Note: this process will have to be repeated whenever the unit is disconnected from the power supply. If the wrong code number is entered, the numbers will remain on the display and the unit will not operate. If this occurs, follow the procedure below: – press and hold the bnd (4) button for approximately three seconds (‘code in’ appears on the display). – enter the correct code number. If the wrong code number is entered three times, a time delay period of one hour commences. After one hour, you can try again. Each time another incorrect code is entered, another hour delay will be activated until the correct code is entered. Cats indicator to warn potential thieves that your unit is protected by a computer anti-theft system, an indicator light (8) flashes whenever the starter switch is turned off. This light can be either activated or deactivated by the following procedure: – turn off the vehicle’s starter switch. – press and hold the bnd button (4) for approximately three seconds.

download
Removal Procedure 1. Check to ensure that the park brake is fully released. 2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle . 3. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation (4 Lug Wheel) or Tire and Wheel Removal and Installation (5 Lug Wheel) . Fig. 5: View Of Brake Drum Courtesy of GENERAL MOTORS CORP. 4. Remove the brake drum. 5. If the brake drum is to be reinstalled to the vehicle, use the J 41013 to clean any rust or corrosion from the hub/flange mating surface of the brake drum. If necessary, carefully remove any corrosion from the edge of the drum braking surface in order to ease installation. 6. Use the J 42450-A to clean the wheel hub flange. Installation Procedure Fig. 6: View Of Brake Drum Courtesy of GENERAL MOTORS CORP. 1. Adjust the drum brakes. Refer to Drum Brake Adjustment. 2. Install the brake drum. 3. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation (4 Lug Wheel) or Tire and Wheel Removal and Installation (5 Lug Wheel) . 4. Apply the brakes approximately three times in order to seat and center the brake shoes within the drum. 5. Lower the vehicle.